Pike Precision 2 F3G Light, LDS and wing servos, Lemon Yellow/White/Black, New Slim Fuse

Pike Precision 2 F3G Light C68, LDS and wing servos installed, Lemon Yellow/White/Black. New slim fuse. 

• Includes protective covers and ballast/spacers
• LDS and Wing Servos Installed-
• Ailerons- KST X10 Mini
• Flaps- KST X10 Mini
• Fuse servo tray for MKS 6100 servos
• Requires 30mm spinner
• 1550 grams empty weight (with wing servos)

The new slim fuse is really a step up for the Pike Precision F3G. Easier fuse servo install with separate bottom hatch and removable 3D printed servo tray. The tray is held in place with screws through the wing shoulders. Various trays will be offered for different servos. The new fuse has a 30mm diameter nose and is much more aerodynamic than the old electric fuselage. The nose is 2.4 friendly. 

Pike Precision 2 F3G version available now.
It was created by optimizing the very successful Pike Precision 2, best F3B model for the last two held World Championships F3B World Champion 2019 - Andreas Böhlen SUI and World Champion 2017 Bernhard Flixider AUT.
Strength and weight optimization of the entire model structure was carried out.
For better and easier control of the model in the thermal role, he got a 7.5° joiner instead of the original 6°.
The best equipment for F3G Pike Precision 2 F3G
Aluminum LDS - Samba model
Motor: Powerline 1520/10 TURBO F3G
Controller: YGE 65 or Castle Talon 60
Lipo HOT LIPS VHD 14,8V 1300 mAh 4S 90-150 C
Propeller: GM C.L. 15/10
Spinner: GM C.L.30/6
The minimum FAI RTF weight is 2224g. With the above components, the stated weight can be easily achieved.
Of course, for fun flying is possible use a cheaper engine - Dualsky outruner XM3045- EG8

Recommended setups for F3G or general sport flying.

Option 1-Setup for fun flying (cheap but good)
RTF weight with F3B C80 version is 2100g.
RTF weight with Light 68 version is 1770g.

Motor : Dualsky XM3045EG-8 (or Dualsky XM3040EG-9 with 9x6)
XM3045EG-8 can be used with full power for more than 30seconds (aerobatic flying with several climbs)
ESC: Castle Talon 60
Battery: 600-1600mah 4S
Prop: GM 10x6 or GM 10x6C.L (can be bought from Samba or Samba dealers)
Spinner: GM 30/5C.L
- Installation servos in fuse 2 x MKS 6100HV under wing, behind joiner,
- Installation motor, controller, settings, etc,

Option 2-Setup for F3G Class

RTF weight with F3B C80 version is 2180g.
RTF weight with Light 68 version is 1850g.


- Motor: Powerline 1520 TURBO F3G,
- Controller: YGE 65,
or
- Castle Talon 60,
- Lipo HOT LIPS VHD 14,8V 1300 mAh 4S 90-150 C,

- Propeller: GM 16x8,
- Spinner: GM 30/6,
- Installation servos in fuse 2 x MKS 6100HV under wing, behind joiner
- Installation motor, controller, settings, etc,

Option 3-Setup for F3G Class

RTF weight with F3B C80 version is 2160g.
RTF weight with Light 68 version is 1830g.


- Motor: Tenshock EDF 1530 2300 KV 5:1
- Controller: YGE 65,
or
-Castle Talon 60,
- Lipo HOT LIPS VHD 14,8V 1300 mAh 4S 90-150 C
- Propeller: GM C.L. 14x10,
- Spinner: GM C.L. 30/6,
- Installation servos in fuse 2 x MKS 6100HV under wing, behind joiner,
- Installation motor, controller, settings, etc,

For all options
-We recommend servos MKS 6100HV for fuselage
-We recommend servos KST X10, KST X10mini, JRDS 189, 181 or MKS6130 for flaps and
aileron
- Min. FAI RTF weight for F3G class is 2224 g.

All setups are designed for a maximum of 30 seconds engine flight at full power. The interval between flights must be at least 10min.
Cooling holes must be drilled in the engine bulkhead !

Pike Precision 2 - a new design by Benjamin Rodax and Philip Kolb

Evolutionary design
In contrast to many new F3B and F3F model developments that are focusing more on single tasks such as launch height or speed, our development target for the Precision 2 was to get a very well balanced all-round design. However, since F3B and F3F competitions are often won in strong conditions, every endeavour has been made to improve top speed performance whilst at the same time slightly improving launch height on the F3B norm winch. Looking at the well-proven design of the Pike Precision, one has to admit that this is very hard to achieve. Coming from this successful design, all design decisions have been put to test. Adding up all minor improvements led to an overall performance gain that justifies the expenses for the production of a new F3B/F model.
During this evolutionary development process the same design principals and strategies as described in the Pike Precision development article where used. The following article therefore mainly focuses on the evolution from the Pike Precision to the Pike Precision 2.

General layout & wing design
Following the concept of a weighting function to guide the development process, the Pike Precision weighting function was adjusted slightly towards better high speed performance:

To achieve this goal, the key design decision was to reduce wing area. The Pike Precision is often described by pilots to be a “lifty” design. This results mainly from the relative large wing: the plane needs to be flown at a higher take off mass to reach a similar wing loading to most competitors. With the limited power of a standard F3B winch it becomes a challenge to reach competitive launch heights, especially in low wind situations. With the reduced wing area the “ballast efficiency” (meaning the wing loading increase per mass unit) increases. The lower take off mass improves the “winch power per mass unit ratio” and thus helps to improve launch height in low wind situations. The newly optimized wing has 57.7dm2 area and spans 2.98m. The dihedral of three degrees per side ensures easy, vice free handling in slow speeds turns. The wing planform was optimized for minimum induced drag and a perfectly constant relative flap chord of 24% all along the wing span. Taper ratio was chosen slightly more conservative compared to the Pike Precision wing, to improve handling qualities at low Reynolds number/high lift situations e.g. slow speed handling.

According to the weighting function I developed eight airfoils along the span to match lift- and speed requirements and to guarantee safe handling characteristics near maximum lift. The use of high modulus carbon fibers for the spar allowed the airfoil thickness to be slightly reduced. It is now in the range of 8.1% to 7.4% relative thickness which helps to lower pressure drag. Compared to the Precision airfoil design, the very good high lift performance could be preserved. At the same time I managed to improve the performance at high speed/low lift at the expense of a little more airfoil drag at slow speed/high lift conditions. This compromise appears to be justified since at slow speeds lift dependent drag (induced drag) is the dominating drag source.

Team Austria at World Championship F3B 2017
In the middle World Champion F3B 2017 Bernhard Flixeder with his Precision2

Tails & fuselage design
As demonstrated on the Pike Precision, the slim fuselage update helped to improve high speed performance considerably. Since the slim fuselage represents the limit of what is possible with today’s RC gear and construction techniques, the slim fuselage design was kept with minor modifications.
Also, the two piece V-tail of the Pike Precision was used again because of the simple construction and the very well proven, safe airfoil design. Even in extreme flight conditions that might occur during recovery from cuts at the slope or critical situations during winch launching, stalling of the tails is rarely to be seen. The reduced wing area of the Precision 2 offers the chance to decrease the v-tail opening angle and still have sufficient longitudinal stability and static margin. At the same time the decreased V-tail angle improves directional stability and provides favorable yaw damping characteristics. Furthermore the rudder power is increased which results in nice harmony of the controls around all three axis.

Benjamin Rodax